My Cart: 0 item(s)

Product Search
Product Search

Secure Checkout
P12A Auth Florence Apartment Intercom, Dual Entrance Station, 5/6 Wire
    P12A Auth Florence Apartment Intercom, Dual Entrance Station, 5/6 Wire
    Purchase P12A Auth Florence Apartment Intercom, Dual Entrance Station, 5/6 Wire
    • SKU: Auth_Florence_P12A_Intercom
      P12A Auth Florence Apartment Intercom, Dual Entrance Station, 5/6 Wire

    • $37.90

    •  

    P12A (P12A) Auth Florence Dual Entrance Intercom
    Standard dual entrance with four momentary push buttons. The buttons are marked talk, listen, entry 1, and entry 2. Made of high impact white plastic. 8” H x 5 1/2” W x 1/2” D. System Operation - The Auth Florence Six Wire System allows for two-way conversation between an apartment. and a building entrance. A visitor initiates a call to an apartment using a push-button on the lobby panel. The tenant uses the talk and listen buttons on the apartment station alternately to communicate with the visitor. The tenant may allow the visitor to enter by pushing the door button on the apartment station. Dual Entrance Description – The P12A is designed for dual entrance systems using the AF1000 with the RB03 relay. The P12A provides two-way communication between an apartment and two building entrances.

    Wiring Requirements For 6 Wire Stations- Five common wires and one unique signal wire per apartment.

    Dimensions: 8" Height, 5.5" Width, 1/2" Depth
    Troubleshooting Auth-Florence Apartment Intercom System

    Entire System Dead
    Check for 16 VAC at transformer secondary and 120 VAC at transformer primary. If LED is illuminated, review field wiring and perform direct test using one of the apartment stations to eliminate field wiring.

    No Talk
    Check wiring to terminals C and T, and check whether wiring to entrance panel speaker is shorted or open. Suite station can be swap tested with another working unit.

    No Listen
    Check wiring to terminals C and PT, or for short between terminals C and T. Check to see if wiring to entrance panel speaker is shorted or open. Suite station can be swap tested with another working unit.

    No Door Operation
    Check wiring to door release for shorts and opens, or for defective door release. Confirm that shunts are properly set for door release type and that connections to appropriate output have been made. Check wiring to terminals C and D, or PDR and SC (depending upon suite station type).

    No Call Tone
    Check wiring to terminal B or BW to entrance panel, related entrance panel call buttons, and suite station SIG terminal. Suite station can be swap tested with another working unit.

    Excessive Hum or Distortion
    Check whether wiring is installed too close to electrical wiring or electrical devices; amplifier installed too close to transformers or other electrical devices; twisted pair wiring not used as required; or amplifier voice volume set too high.

    Radio Interference
    Connect G terminal from amplifier to electrical ground. Note: This connection is not shown on the wiring diagram, since the situation is not always improved by adding it. If the problem persists, consult the factory or service representative.

    Oscillation (feedback or howling)
    Reduce the voice volume until oscillation is eliminated. Check the entry panel speaker for 45 ohms.

    Signal Flow and Theory of Operation for AF1000 Amplifier and Apartment Intercom System
    The following example describes an apartment intercom system using a AF1000 in conjunction with a 4-wire suite station. Refer also to Figure 5 on page 8.

    Call Button
    Pressing a suite station call button on the entrance panel routes the call tone from the B or BW terminal on the AF1000 to the SIG terminal (tone in) on the associated suite station. This signal then passes through the speaker and returns to the AF1000 via the C terminal (audio common). If the warble tone is in use and the entrance tone feature is active, the tone will also be heard through the entrance panel speaker when the call button is pressed.

    Talk Button
    Pressing the talk button at a suite station connects the suite station’s internal speaker to terminals C and T of the AF1000, which serves as an audio input to the amplifier. The audio is then amplified and sent to terminals SC and S, which are connected to the entrance panel’s speaker (speaker mode).

    Listen Button
    Pressing the listen button at a suite station connects the suite station’s internal speaker to terminals C and PT (4W) of the AF1000, which serves as an audio output from the amplifier. This allows the suite station to receive the amplified audio being received by the amplifier on terminals SC and S from the entrance panel speaker (microphone mode).

    Door Button
    Pressing the door button at a suite station creates a closure between terminals C and D on the AF1000. This state is sensed by the amplifier and causes the door release to be activated. This state is also triggered by shorting terminals 1 and E as is typically done by a postal lock.